标签: lpc1768

随便google了下，发现貌似没什么人关心这个问题，不过没关系，就让以后的初学者看到后不用再迷茫了。 其实两者是有很大不同的，前者只能通过软件不停查询LPC_GPIOINT-IO2IntStatR或LPC_GPIOINT-IO2IntStatF来获得端口边沿情况，而后者则一般由硬件自动进入中断处理函数。前者清除中断标志用LPC_GPIOINT-IO2IntClr，后者则用LPC_SC-EXTINT。 前者编程示例： void EINTInit( void ) {        LPC_GPIO2-FIODIR  =  ~(1 11);    /* PORT2.11 defined as input       */          LPC_GPIO2-FIODIR      = ~(1 11);          LPC_GPIOINT-IO2IntEnR |=  (1 11);      /* enable rising edge irq         */          LPC_GPIOINT-IO2IntEnF |=  (1 11);       /* enable falling edge irq         */} }   int main(void) {          While(1)          {            if(LPC_GPIOINT-IO2IntStatF!=0x0)                        LED_On (0xff);                                                //点亮LED               if(LPC_GPIOINT-IO2IntStatR)                      LED_Off (0xff);                                               //熄灭LED            LPC_GPIOINT-IO2IntClr |= (1 11);     /* clear pending interrupt         */   }   }   后者编程示例： void EINTInit( void ) {        LPC_GPIO2-FIODIR  =  ~(1 10);    /* PORT2.10 defined as input       */ LPC_PINCON-PINSEL4 = 0x00100000;            // set P2.10 as EINT0 LPC_SC-EXTMODE = 0x01;                           /* INT0 edge trigger */ LPC_SC-EXTPOLAR = 0x01;                 /* INT0 is rising edge by default */   NVIC_EnableIRQ(EINT0_IRQn);                       //使能EINT0中断 } void EINT0_IRQHandler() {          LPC_SC-EXTINT = 0x01;         //EXIT0中断状态清零，在P2.10 }

  调试LPC1768， NXP的库好像不如Luminary的好用（大家都这么说，也就跟着人云亦云了）。对照LPC1768的手册看了看Keil例程的PLL0配置过程，记录如下：                #if (CLOCK_SETUP)                       /* Clock Setup                        */   LPC_SC-SCS       = SCS_Val;          // 启用外部主时钟   if (SCS_Val (1 5)) {             /* If Main Oscillator is enabled      */     while ((LPC_SC-SCS (16)) == 0);/* Wait for Oscillator to be ready    */   } //PLL倍频出来的时钟送给CPU前的分频，CCLKCFG_Val=3，为4分频   LPC_SC-CCLKCFG   = CCLKCFG_Val;      /* Setup Clock Divider                */   LPC_SC-PCLKSEL0  = PCLKSEL0_Val;     /* Peripheral Clock Selection         */   LPC_SC-PCLKSEL1  = PCLKSEL1_Val;   LPC_SC-CLKSRCSEL = CLKSRCSEL_Val;    /* Select Clock Source for PLL0       */ #if (PLL0_SETUP) //PLL0CFG_Val = 0x00050063， 5为pre-div的值既N，所以除数为N+1=6 // 0x63为乘数M，M+1=100，记得要把16进制换算为10进制 //Fcco = 2*100*12/6 = 400，然后再除以CPU clock的4，即该设置主频为100M   LPC_SC-PLL0CFG   = PLL0CFG_Val;   LPC_SC-PLL0CON   = 0x01;             /* PLL0 Enable                        */ //确认序列   LPC_SC-PLL0FEED  = 0xAA;   LPC_SC-PLL0FEED  = 0x55;   while (!(LPC_SC-PLL0STAT (126)));/* Wait for PLOCK0                    */   LPC_SC-PLL0CON   = 0x03;             /* PLL0 Enable Connect              */   LPC_SC-PLL0FEED  = 0xAA;   LPC_SC-PLL0FEED  = 0x55; #endif #if (PLL1_SETUP)   LPC_SC-PLL1CFG   = PLL1CFG_Val;   LPC_SC-PLL1CON   = 0x01;             /* PLL1 Enable                        */   LPC_SC-PLL1FEED  = 0xAA;   LPC_SC-PLL1FEED  = 0x55;   while (!(LPC_SC-PLL1STAT (110)));/* Wait for PLOCK1                    */   LPC_SC-PLL1CON   = 0x03;             /* PLL1 Enable Connect              */   LPC_SC-PLL1FEED  = 0xAA;   LPC_SC-PLL1FEED  = 0x55; #else   LPC_SC-USBCLKCFG = USBCLKCFG_Val;    /* Setup USB Clock Divider            */ #endif   LPC_SC-PCONP     = PCONP_Val;        /* Power Control for Peripherals      */   LPC_SC-CLKOUTCFG = CLKOUTCFG_Val;    /* Clock Output Configuration         */ #endif   /* Determine clock frequency according to clock register values             */   if (((LPC_SC-PLL0STAT 24)3)==3) {/* If PLL0 enabled and connected      */     switch (LPC_SC-CLKSRCSEL 0x03) {       case 0:                           /* Internal RC oscillator = PLL0     */       case 3:                           /* Reserved, default to Internal RC   */         SystemFrequency = (IRC_OSC *                           ((2 * ((LPC_SC-PLL0STAT 0x7FFF) + 1)))  /                           (((LPC_SC-PLL0STAT 16) 0xFF) + 1)    /                           ((LPC_SC-CCLKCFG 0xFF)+ 1));         break;       case 1:                           /* Main oscillator = PLL0            */      //待Pll锁定和连接后PLL0STAT中有M和N，可以计算出实际频率         SystemFrequency = (OSC_CLK *                           ((2 * ((LPC_SC-PLL0STAT 0x7FFF) + 1)))  /                           (((LPC_SC-PLL0STAT 16) 0xFF) + 1)    /                           ((LPC_SC-CCLKCFG 0xFF)+ 1));         break;       case 2:                           /* RTC oscillator = PLL0             */         SystemFrequency = (RTC_CLK *                           ((2 * ((LPC_SC-PLL0STAT 0x7FFF) + 1)))  /                           (((LPC_SC-PLL0STAT 16) 0xFF) + 1)    /                           ((LPC_SC-CCLKCFG 0xFF)+ 1));         break;     }   } else {     switch (LPC_SC-CLKSRCSEL 0x03) {       case 0:                           /* Internal RC oscillator = PLL0     */       case 3:                           /* Reserved, default to Internal RC   */         SystemFrequency = IRC_OSC / ((LPC_SC-CCLKCFG 0xFF)+ 1);         break;       case 1:                           /* Main oscillator = PLL0            */         SystemFrequency = OSC_CLK / ((LPC_SC-CCLKCFG 0xFF)+ 1);         break;       case 2:                           /* RTC oscillator = PLL0             */         SystemFrequency = RTC_CLK / ((LPC_SC-CCLKCFG 0xFF)+ 1);         break;     }   }