tag 标签: pioneer

相关博文
  • 热度 17
    2013-11-11 21:37
    1484 次阅读|
    0 个评论
    In the latter part of the 80s, I was on a bike ride with my two sons, one about eight was on his own bike and the other, who was maybe two, was strapped into a kid seat over the rear wheel of my bike. On our usual ride, which runs through a small neighbourhood along the river, something electronic looking caught the corner of my eye. Funny how that works, but I'm sure many of you know exactly what I mean. It was the evening before trash day and partway down a small side alley I saw something sticking up out of a trash can with just the back panel visible. We rode on over for a closer look and I pulled on it. Other bits of garbage slid back into the can as a Pioneer SX-535 receiver revealed itself—this might be a real score!   Even spending time in the trash, it only had a small scar on the top back edge of the wood cabinet. Not a problem as far as I was concerned. The lady of the house spotted us, and after a short conversation summarised, "It doesn't work anymore," and granted that I could have it. I tried riding with it under one arm, but the terrain here was rough and it didn't take long to conclude I might either drop it or dump my bike with my young son strapped in. Rationally, I set the receiver back down and we rode for home; driving back to pick up the unit. Analogue wasn't my strength, and my test equipment at the time was a really cheap analogue voltmeter and a similarly priced soldering iron, but that wasn't going to stop me from trying to impress my son. I borrowed speakers from the living room and confirmed "it doesn't work anymore." It lit up, and the radio signal strength worked, but there was no sound, no clicks, no pops, no radio hiss, no nuthin'. And dare I need to say—no schematic.   With the cover off. We looked inside and saw cracks and bulges in the power transistors. The rest of the PCB and parts looked great, and a little probing said the power supply was good (reading plus and minus 30v). There was a pattern to the layout that let me easily check both channels and the voltages "seemed" OK.   Here's an undamaged view of the PCB and power transistors.   I thought it was a shame the fuses didn't protect anything, they were all good. I'm pondering the failure? short circuit? weak design? operator error? overheating? Perhaps a stray strand on one speaker lead shorted the channel? Maybe, but could that blow both channels? I'm thinking it was likely that the design couldn't stand up to heavy use, and the owners were likely running it hard. We pulled the power transistors out, but with bubbled and burnt cases, it took quite a study to extract what I thought to be the part numbers. Off we went to the local electronics supply house to see if they had the parts. They had the "Sam's" schematics for most everything—except this receiver. But I had pulled a good-enough part number for the NPN, and they recommended the complementary part. As I recall it was about $20 for a pair. I was willing to risk $20 on this dumpster salvage, but I wasn't ready to go "all in" for $40 since I didn't know if I had the fix. Under a watchful eye my son soldered in the parts. I put my voltmeter on the output, and gave the power switch a flip. I saw just a tiny pulse on the needle of the voltmeter as the power supplies came to life and it settled back down to about zero. As I probed about, all looked pretty good. I made a small adjustment to the bias drive for the power transistors, mostly because the control was there since I didn't see any effect on the meter. I powered down once more and attached the speaker.   Part of the schematic I didn't have back then – showing the power amp for one channel. Another flip of the power switch, and sound came out! I did basic voltage checks again—I sure wish I would have had a scope back then. I assumed the bias I was adjusting would affect the zero-crossing and quiescent drive, and I gently cranked up the volume. We're thinking—this is a pretty decent amp for the money! Off to the supply store for another pair of parts. I soldered those parts in, switched it on, was probing the circuit, making the small adjustments, and "poof"—the smoke erupted out of the parts I had just put into play. Argh! Had my son not been a witness, I would've let out a few choice words. Clumsy me, with a dull-tipped voltmeter probe, I slipped, and paid the price. OK, now I was into this dumpster salvage for $40; do I cut my losses, or run it on up for another $20. I made one more trip to the electronics supply, tried not to establish much eye contact for fear the guy might ask, "What takes three pairs of parts?" Successfully installed and this time I sharpened the probe tips before the next power check—all turned out well. That amp served the basement family room in the house for nearly 15 years. Then one day, when I came home from work, I learned "it doesn't work anymore..." That's when it joined the dead device shelf, taking up residence with an old Hi-Fi stereo VHS deck, an old cassette deck, and more...   What do I miss most about that receiver? I have to say, it's the high-contrast black labels on the silver panel—very easy to read! For some reason, everything new seems to be dark lettering on a black panel and these eyes don't appreciate it. About the author My dad was quite a mechanic and co-owner in a local machine shop. We kids got to play with tools beyond our years since we could stand—drill presses, sheet metal benders, metal lathes, and more. In the garage one day, I must've been about six (it was the mid 60s), I was studying an extension cord. On the end of the cord was a light bulb socket with a 2-prong outlet adapter screwed in. After unscrewing the adapter I asked dad, "What will happen if I put my thumb in there?" He said "try it"—so I did. After that experience, I was hooked on electrical things. I would tear apart motors and old tube radios. In my early teens I managed to "fix" an old BW tube tv, but also had some "experience" with the big lead on the side of the tube. After that I tried to avoid high voltage, but electronics became both my profession and one of my favourite hobbies. David Smart submitted this article as part of Frankenstein's Fix, a design contest hosted by EE Times (US).  
相关资源
  • 所需E币: 0
    时间: 2020-9-8 19:03
    大小: 896.42KB
    上传者: Goodluck2020
    PIONEERHEADPHONE主要情报一览
  • 所需E币: 3
    时间: 2020-1-9 13:51
    大小: 12.78MB
    上传者: givh79_163.com
    PSoC4Pioneerkit项目照片……
  • 所需E币: 5
    时间: 2020-1-9 13:52
    大小: 2.88MB
    上传者: wsu_w_hotmail.com
    PSoC4Pioneerkit项目软件_ThermostatControl……
  • 所需E币: 4
    时间: 2020-1-9 13:52
    大小: 1.67MB
    上传者: wsu_w_hotmail.com
    :项目名称、实现的功能、应用、创新点、PSoC4内部资源利用的充分性、采用PSoC4和其他产品在所用开发时间上的对比、该设计中采用CypressPSoC4产品比其他产品所具有的不可替代的优势基于PSoC4Pioneerkit温度采集及控制——ARMCortexTM-M0应用◆项目名称基于PSoC4Pioneerkit温度采集及控制◆功能应用及创新点1.利用定时器制作软件时钟,实时显示小时、分钟、星期。2.利用内部温度传感器和ADC采集检测芯片温度。3.利用SegmentLCD显示小时、分钟、星期和当前芯片温度等信息。4.PWM驱动RGB三色LED。设置温度小于当前温度5℃时,绿色LED亮;设置温度大于当前温度5℃时,红色LED亮;其他温度条件,蓝色LED亮。5.5个CapSense容式触摸按键,分别是上键、下键、确定键、设置键、时钟键。通过这5个按键可以设置当前时间,改变当前设置温度。6.利用仿真型Em_EEPROM存储掉电时的时间和设置温度。7.利用外部中断检测一个机械按键,按一下该机械按键RGB三色LED全部点亮,呈现白色,再按一下该机械按键RGB三色LED按照功能4规律点亮。◆PSoC4内部资源利用的充分性该项目利用了以下内部资源:1.时钟源:该项目用到了多处时钟源,如定时器,PWM,SegmentLCD,其中定时器的时钟源用的是1KHz,PWM的时钟源用的是100KHz,SegmentLCD的时钟源用的是12MHz,时钟源的设置只是频率不同,不再逐一介绍。[pic][pic]2.定时器Timer:定时器模块的clock输入1KHz的时钟信号,开启定时器中断interrput,设定每20mS产生一次中断。[pic][pic][pic]在主函数中启用……